Download the latest drivers for your Bematech Port Devices to keep your Computer up-to-date. Belkin Bluetooth V2.1 Driver Download. So we were pleased at how intuitive and Bematech Mp 2100 Th Fi Driver this programs layout felt. • MP-2100 TH User´s Manual P/N: 5686. Rev.1.1 November 2005 (First edition: July 2004) Copyright by Bematech S.A. Curitiba-PR, Brazil. © All rights reserved. No part of this publication may be copied, reproduced, adapted or translated without the prior written permission of Bematech S.A., except when allowed by patent rights. • MP-2100 TH Revision 1.1 EMC and Safety Standards Applied Product Name: MP-2100 TH Model Name: All *EMC is tested using an EPSON PS180 power supply Europe: CE marking Safety: EN60950 North America: EMI: FCC Class A Unauthorized changes or modifications on the equipment could void the certifications described in this page. • To ensure safety, unplug this product before leaving it unused for an extended period. In this case, please be sure to place a piece of paper between the platen and the paper roll, in the thermal mechanism, to avoid damage when restarting the printer. * Note that this equipment was developed complying with international safety standards and therefore contains only limited flammability components. • Summar Summar y y y y y Summar Summar Chapter 1 - Presentation. Chapter 2 - Technical Specifications MP-2100 TH. Chapter 3 - Communication Interfaces. Serial Interface. Parallel Interface. USB Interface. Chapter 4 - Character Tables. • Chapter 1 Presentation Printer Description Explanations about how each MP-2100 TH part operates are described in this manual. Whenever some note refers to one of the parts, the corresponding number of such part will be in brackets, next to the note. • Figure 5 Turn on the printer using the on / off switch located on the printer. Check, also in the panel, if the Power LED is lit. If no paper is present, the Paper LED will also be lit. • Figure 6 The MP-2100 TH offers easy automatic paper placement. Just position it in the gutter entrance pushing it inwards (Figures 6 and 7). That makes the mini-printer to activate the automatic paper advance mechanism, thus making the paper replacing easier. • Self-testing To run a self-test press and hold the Paper Feed switch and turn it on. When the printer starts printing, the paper feed button can be released. A message will be printed asking you waiting for the self-test. In the self-test you will find the printer firmware version. • Chapter 2 Technical Specifications Characteristics Printing Features Printing Paper Entry Buffer Communication Interfaces Power Supply Detection Functions Environmental Conditions Size Life Expectation - MCBF Power Activation Mass Cutter Specifications Method: lines of thermal dots Dot Density: 8 dots per mm Width: 72 mm Speed. • RTS/CTS mode In this mode, the printer’s RTS line controls the flow of data sent from the host’s TX line and received by the printer’s RX pin. In this case, when the printer’s RTS signal is low (+12V) the printer requests the host to send data. When the RTS signal is high (-12V) the printer tells the host to stop sending data. • Parallel Interface The unidirectional parallel interface has the following specifications: • Synchronization: Externally supplied Strobe signal • Handshaking: Ack and Busy signal • Signal levels: TTL compatible • Data transmission: 8-bit parallel Parallel Interface Pin Assignments Associated Signal pin return pin Signal /STROBE Data 1. • Bulk mode with a “B” receptacle as show below. The USB cable must have in one side an “A” plug to connect in the host, and in the other side an “B” plug to connect in the printer. The printer is self-powered and does not draw power from the standard type B USB interface cable. • Chapter 4 Character T Character T ables ables Character T Character T Character Tables ables ables ASCII Table The codes from 00h up to 7Fh are shown below: Characters from 00h to 1Fh are “command characters” and therefore are not represented in the following tables Code Page 850 User’s Manual. • MP-2100 TH Revision 1.1 Code Page 437 Code Page 858. • User’s Manual Tabela de Caracteres Code Page 860. • -2100 TH Commands This section contains general information regarding the MP-2100 TH commands. The MP-2100 TH printer has a series of programming commands that may be used in the remote mode. Two types of commands can be sent: Direct Command In this mode, a simple ASCII code is enough to command the printer. • Command Tables Command T ables ables Operation ASCII Description ESC @ Initializes the printer ESC b n Enable (1): Status drawer sensor Disable (0): Status paper sensor ESC v n Activate drawer (n miliseconds) -50ms.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
September 2018
Categories |